ADPCM

From NeoGeo Development Wiki
Revision as of 03:12, 16 February 2017 by Furrtek (talk | contribs) (→‎ADPCM-B)
Jump to navigation Jump to search

Adaptive Differential Pulse Code Modulation is a lossy audio compression algorithm. It is essentially PCM with dynamic quantizing step adaptation. See [Wikipedia article] for more general informations.

The NeoGeo's YM2610 uses this format for samples stored in the V ROMs or PCM files. Each sample is coded in 4 bits and approximately reconstituted as 12 or 16 bits during playback.

Note that the Yamaha ADPCM format is different from the common IMA and Microsoft ADPCM formats. See ADPCM codecs for encoding and decoding tools.

The NeoGeo CD can't use ADPCM-B.

ADPCM-A

The ADPCM-A part has 6 channels with a fixed playback frequency of: 8MHz (8M) / 12 (prescaler) / 6 clocks per access / 6 channels = ~18.5185kHz.

Audio is compressed as 4bit per sample and played back as 12bit.

Registers

Address (Z80 port 6) Data (Z80 port 7) Value on reset
$00
Bit 7 6 5 4 3 2 1 0
Def Dump -CH6 ONCH5 ONCH4 ONCH3 ONCH2 ON CH1 ON
$00 'Dump' is the key on/off bit. Write 0 to start playing specified channels and write 1 to stop playing.
$01
Bit 7 6 5 4 3 2 1 0
Def - Master volume
$00 Actually an attenuator, 0 is the loudest.
$08~$0D (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def L R-Channel volume
$00 Actually an attenuator, 0 is the loudest. L/R routes the output to the left and/or right channels.
$10~$15 (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 LSB
$00 All ADPCM addresses must match a 256-byte boundary (bits 0~7 = 0)
$18~$1D (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 MSB
$00
$20~$25 (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 LSB
$00
$28~$2D (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 MSB
$00

ADPCM-B

The ADPCM-B part only has 1 channel, but the playback frequency can be set from 1.85kHz to: 8MHz (8M) / 2 / 12 (prescaler) / 6 clocks per access = ~55.555kHz.

Audio is compressed as 4bit per sample and played back as 16bit.

Registers

See ADPCM for details on this part's operation.

Address (Z80 port 4) Data (Z80 port 5) Value on reset
$10
Bit 7 6 5 4 3 2 1 0
Def Start -Repeat-Reset
$00 Repeat: loop when end address is reached. Reset: clears Start and Repeat.
$11
Bit 7 6 5 4 3 2 1 0
Def L R-
$00 Left/Right channel output
$12
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 LSB
? All ADPCM addresses must match a 256-byte boundary (bits 0~7 = 0)
$13
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 MSB
?
$14
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 LSB
?
$15
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 MSB
?
$19
Bit 7 6 5 4 3 2 1 0
Def Delta-N (L)
? Playback rate is f = 8M / 12 / 12 / (65535 / Delta-N) = 55555 * (Delta-N / 65535) Hz
$1A
Bit 7 6 5 4 3 2 1 0
Def Delta-N (H)
?
$1B
Bit 7 6 5 4 3 2 1 0
Def ADPCM-B channel volume
? Loudest is $FF

Format

Samples can be any size from 256 bytes to 1MiB, in 256 bytes steps. Samples cannot cross 1MB pages (the 4 MSBs of the end address should be equal to the start address). Be sure to organize/map your data correctly.

=Programming-

See YM2610 registers: ADPCM-A and ADPCM-B

Drifting

Decoded ADPCM audio slowly drifting upwards and hitting a chunk of garbage data.

Since the algorithm is based on the difference between samples, it is prone to drifting if buggy codecs or bad data are used.

Clean data should always produce a zero-centered signal when decoded.

If a cartridge has contact issues for example, the YM2610 will read corrupt data and the decoder will make the output value randomly "jump" everywhere, resulting in a horrendous screeching sound even if only one data line is disconnected.

Many V ROMs contain garbage data at more-or-less regular intervals. Consequently, if the dump is decoded from start to end, the decoder will take the garbage data into account and the decoded audio output will either drift slowly or become brutally offset. This isn't an issue when the game is running because the YM2610 resets the decoder each time a sample is played (also, the sound driver shouldn't be playing garbage data).