Pinouts: Difference between revisions

From NeoGeo Development Wiki
Jump to navigation Jump to search
mNo edit summary
(13 intermediate revisions by 2 users not shown)
Line 1: Line 1:
=A/V connector=
[[File:Av_pinout.png]]
Note: Some home consoles revisions appear to only provide composite video, no separate sync signal.
=Cartridges=
=Cartridges=
==Signal names==


*6M, 12M, 24M: 6MHz, 12MHz, and 24MHz clock signals
* [[AES cartridge pinout]]
*4MB: 4MHz inverted signal
* [[MVS cartridge pinout]]
*A1~A19: [[68k]] address bus
 
*D0~D15: 68k data bus
=Joypad ports=
*R/W: 68k R/W
*AS: 68k /AS
*/ROMOEL: $000000-$0FFFFF odd byte read
*/ROMOEU: $000000-$0FFFFF even byte read
*/ROMOE: $000000-$0FFFFF read
*/PORTOEL: $200000-$2FFFFF odd byte read
*/PORTOEU: $200000-$2FFFFF even byte read
*/PORTWEL: $200000-$2FFFFF odd byte write
*/PORTWEU: $200000-$2FFFFF even byte write
*/PORTADRS: $200000-$2FFFFF any access
*CR0~CR31: [[C ROM]]s data bus (2*16bits)
*SDRAD0~SDRAD7: ADPCM-A ROM [[YM2610#Multiplexed bus|multiplexed bus]] (data/address)
*SDRA8,SDRA9,SDRA20~SDRA23: ADPCM-A ROM address bus
*SDPAD0~SDPAD7: ADPCM-B ROM multiplexed bus (data/address)
*SDPA8,SDPA9,SDPA10,SDPA11: ADPCM-B ROM address bus
*P0~P23: C ROM and [[S ROM]] address bus (multiplexed)
*PCK1B: Clock to latch C ROM address from P0~P23 ([[NEO-273|mapping]]) on rising edge
*PCK2B: Clock to latch S ROM address from P0~P15 ([[NEO-273|mapping]]) on rising edge
*CA4: C ROM A4
*2H1: S ROM A3
*FIXD0~FIXD7: S ROM data bus


==AES Cartridge==
Special, deep DA-15 connectors with a plastic shield. 10 direct inputs, 3 outputs, 2 power lines.


{| class="regdef" align="center" style="text-align:center;align:right;"
Inputs are pulled high to +5V by [[CRE401]] R-C arrays.
|PROG
|CHA
|-
|[[File:aesprogpinout.png]]
|[[File:aeschapinout.png]]
|}


*: Audio loops only used on NEO-AES systems (info from [[User:Kyuusaku]])
Outputs are open collector through 22 ohms resistors (not pulled high).


==MVS Cartridge==
<center>[[File:Joypad_pinout.png]]</center>


{| class="regdef" align="center" style="text-align:center;align:right;"
=JAMMA=
|CHA bottom
|CHA top
|PROG bottom
|PROG top
|-
|[[File:mvscartchabot.png|200px]]
|[[File:mvscartchatop.png|200px]]
|[[File:mvscartprgbot.png|200px]]
|[[File:mvscartprgtop.png|200px]]
|}


See [[JAMMA connector pinout]].


<span style="color:#FF0000"><B>Beware !</B> Pinouts found elsewhere have ROMOE/4MB swapped, it's an error on the original schematics. ROMOE is on pin 33 bottom, 4MB is on pin 34 bottom.</span>
=Memory card=


=Joypad ports=
See [[Memory card pinout]].


Inputs are pulled high to +5V.
=MVS boards=


<center>[[File:Joypad_pinout.png]]</center>
See [[MVS board connectors pinouts]].


=JAMMA connector=
=[[Multiplayer]] jack=
Infos from [[http://www.hardmvs.com HardMVS.com]]


{| class="regdef"
RS-485 pair + ground. Use a stereo cable only !
|bgcolor="#DDDDDD"|GND
|'''A'''
|'''1'''
|bgcolor="#DDDDDD"|GND
|-
|bgcolor="#DDDDDD"|GND
|'''B'''
|'''2'''
|bgcolor="#DDDDDD"|GND
|-
|bgcolor="#DD8888"| +5V
|'''C'''
|'''3'''
|bgcolor="#DD8888"| +5V
|-
|bgcolor="#DD8888"| +5V
|'''D'''
|'''4'''
|bgcolor="#DD8888"| +5V
|-
|
|'''E'''
|'''5'''
|
|-
|bgcolor="#DDDD88"| +12V
|'''F'''
|'''6'''
|bgcolor="#DDDD88"| +12V
|-
|Key
|'''H'''
|'''7'''
|Key
|-
|Coin counter #2
|'''J'''
|'''8'''
|Coin counter #1
|-
|Lockout coil #2
|'''K'''
|'''9'''
|Lockout coil #1
|-
|bgcolor="#DD8844"|Left speaker +
|'''L'''
|'''10'''
|bgcolor="#DD8844"|Right speaker +
|-
|Test switch
|'''M'''
|'''11'''
|bgcolor="#DD8844"|Mono audio +
|-
|bgcolor="#44FF44"|Video green
|'''N'''
|'''12'''
|bgcolor="#FF4444"|Video red
|-
|bgcolor="#FFFF44"|Video sync
|'''P'''
|'''13'''
|bgcolor="#4444FF"|Video blue
|-
|Service switch
|'''R'''
|'''14'''
|bgcolor="#DDDDDD"|Video GND
|-
|Coin switch #4 P2
|'''S'''
|'''15'''
|Coin switch #3 P1
|-
|Coin switch #2 P2
|'''T'''
|'''16'''
|Coin switch #1 P1
|-
|P2 Start
|'''U'''
|'''17'''
|P1 Start
|-
|P2 Up
|'''V'''
|'''18'''
|P1 Up
|-
|P2 Down
|'''W'''
|'''19'''
|P1 Down
|-
|P2 Left
|'''X'''
|'''20'''
|P1 Left
|-
|P2 Right
|'''Y'''
|'''21'''
|P1 Right
|-
|P2 A
|'''Z'''
|'''22'''
|P1 A
|-
|P2 B
|'''a'''
|'''23'''
|P1 B
|-
|P2 C
|'''b'''
|'''24'''
|P1 C
|-
|P2 D
|'''c'''
|'''25'''
|P1 D
|-
|Select down
|'''d'''
|'''26'''
|Select up
|-
|bgcolor="#DDDDDD"|GND
|'''e'''
|'''27'''
|bgcolor="#DDDDDD"|GND
|-
|bgcolor="#DDDDDD"|GND
|'''f'''
|'''28'''
|bgcolor="#DDDDDD"|GND
|}


* Sleeve: Ground
* Ring: D-
* Tip: D+


=CD/CDZ=
=CD/CDZ=
==Power supply connector==
[[File:Cdpow_pinout.png]]
See [[power supply]].


==YM2610 digital audio==
==YM2610 digital audio==
[[File:Cd2_cn7.jpg|Cd2_cn7.jpg]]
[[File:Cd2_cn6.jpg|Cd2_cn6.jpg]]
Clock, L, R ?
 
# OP0
# PHI
# SH2
# SH1
# Analog


==Video and CDDA==
==Video and CDDA==
[[File:Cd2_cn1cn3.jpg|400px]]
[[File:Cd2_cn1cn3.jpg|400px]]
R, V, B, S, Burst, GND ?
Clock, L, R ?


==CD reader==
Video:
# Red
# Green
# Blue
# Sync
# Burst
# GND
 
CDDA:
# LRCK
# DATA
# BCLK
 
==CD drive==
[[File:Cd2_cn4.jpg|400px]]
[[File:Cd2_cn4.jpg|400px]]
See [[CD drive]].


==Power==
==PCB power==
[[File:Cd2_cn5.jpg]]
[[File:Cd2_cn5.jpg]]


=Multiplayer jack=
# 5V CD
To do.
# 10V CD
 
# 5V logic
# Ground


[[Category:Chips]]
[[Category:Chips]]
[[Category:Base system]]
[[Category:Base system]]

Revision as of 18:59, 6 September 2018

A/V connector

Note: Some home consoles revisions appear to only provide composite video, no separate sync signal.

Cartridges

Joypad ports

Special, deep DA-15 connectors with a plastic shield. 10 direct inputs, 3 outputs, 2 power lines.

Inputs are pulled high to +5V by CRE401 R-C arrays.

Outputs are open collector through 22 ohms resistors (not pulled high).

JAMMA

See JAMMA connector pinout.

Memory card

See Memory card pinout.

MVS boards

See MVS board connectors pinouts.

Multiplayer jack

RS-485 pair + ground. Use a stereo cable only !

  • Sleeve: Ground
  • Ring: D-
  • Tip: D+

CD/CDZ

Power supply connector

See power supply.

YM2610 digital audio

Cd2_cn6.jpg

  1. OP0
  2. PHI
  3. SH2
  4. SH1
  5. Analog

Video and CDDA

File:Cd2 cn1cn3.jpg

Video:

  1. Red
  2. Green
  3. Blue
  4. Sync
  5. Burst
  6. GND

CDDA:

  1. LRCK
  2. DATA
  3. BCLK

CD drive

File:Cd2 cn4.jpg See CD drive.

PCB power

File:Cd2 cn5.jpg

  1. 5V CD
  2. 10V CD
  3. 5V logic
  4. Ground