Pinouts: Difference between revisions

From NeoGeo Development Wiki
Jump to navigation Jump to search
mNo edit summary
 
(22 intermediate revisions by 3 users not shown)
Line 1: Line 1:
=MVS Cartridges=
=A/V connector=


{| class="regdef" align="center" style="text-align:center;align:right;"
[[File:Av_pinout.png]]
|CHA bottom
|CHA top
|PROG bottom
|PROG top
|-
|[[File:mvscartchabot.png|200px]]
|[[File:mvscartchatop.png|200px]]
|[[File:mvscartprgbot.png|200px]]
|[[File:mvscartprgtop.png|200px]]
|}


Signal names:
Note: Some home consoles revisions appear to only provide composite video, no separate sync signal.
*A1~A19: [[68k]] address bus
*D0~D15: 68k data bus
*R/W: 68k R/W
*AS: 68k /AS
*ROMOEL: $000000-$0FFFFF odd byte read
*ROMOEU: $000000-$0FFFFF even byte read
*ROMOE: $000000-$0FFFFF read
*PORTOEL: $200000-$2FFFFF odd byte read
*PORTOEU: $200000-$2FFFFF even byte read
*PORTWEL: $200000-$2FFFFF odd byte write
*PORTWEU: $200000-$2FFFFF even byte write
*PORTADRS: $200000-$2FFFFF any access
*SDPAD0~SDPAD7, SDRAD0~SDRAD7: [[V ROM]](s) data bus(ses) ?
*CR0~CR31: [[C ROM]]s data bus
*SDRAD0~SDRAD7: ADPCM-A ROM [[YM2610#Multiplexed bus|multiplexed bus]] (data/address)
*SDRA8,SDRA9,SDRA20~SDRA23: ADPCM-A ROM address bus
*SDPAD0~SDPAD7: ADPCM-B ROM multiplexed bus (data/address)
*SDPA8,SDPA9,SDPA10,SDPA11: ADPCM-B ROM address bus
*P0~P23: C ROM and [[S ROM]] address bus (multiplexed)
*PCK1B: Clock to latch C ROM address from P0~P23
*PCK2B: Clock to latch S ROM address from P0~P15
*CA4: C ROM A4
*2H1: S ROM A3
*FIXD0~FIXD7: S ROM data bus


=AES Cartridges=
=Cartridges=


To do.
* [[AES cartridge pinout]]
* [[MVS cartridge pinout]]


=Joypad ports=
=[[Joypad]] ports=


Inputs are pulled high to +5V.
Special, deep DA-15 connectors with a plastic shield. 10 direct inputs, 3 outputs, 2 power lines.
 
Inputs are pulled high to +5V by [[CRE401]] R-C arrays.
 
Outputs are open collector through 22 ohms resistors (not pulled high).


<center>[[File:Joypad_pinout.png]]</center>
<center>[[File:Joypad_pinout.png]]</center>


=JAMMA connector=
=JAMMA=
Infos from [[http://www.hardmvs.com HardMVS.com]]
 
See [[JAMMA connector pinout]].
 
=Memory card=
 
See [[Memory card pinout]].
 
=MVS boards=
 
[[MV4]]
 
* [[MVS board connectors pinouts|MVS MV-4 board connectors pinouts]].
 
[[MV6]]
 
* [[MVS MV-6 daughter board connectors pinouts]].


{| class="regdef"
=[[Multiplayer]] jack=
|bgcolor="#DDDDDD"|GND
|'''A'''
|'''1'''
|bgcolor="#DDDDDD"|GND
|-
|bgcolor="#DDDDDD"|GND
|'''B'''
|'''2'''
|bgcolor="#DDDDDD"|GND
|-
|bgcolor="#DD8888"| +5V
|'''C'''
|'''3'''
|bgcolor="#DD8888"| +5V
|-
|bgcolor="#DD8888"| +5V
|'''D'''
|'''4'''
|bgcolor="#DD8888"| +5V
|-
|
|'''E'''
|'''5'''
|
|-
|bgcolor="#DDDD88"| +12V
|'''F'''
|'''6'''
|bgcolor="#DDDD88"| +12V
|-
|Key
|'''H'''
|'''7'''
|Key
|-
|Coin counter #2
|'''J'''
|'''8'''
|Coin counter #1
|-
|Lockout coil #2
|'''K'''
|'''9'''
|Lockout coil #1
|-
|bgcolor="#DD8844"|Left speaker +
|'''L'''
|'''10'''
|bgcolor="#DD8844"|Right speaker +
|-
|Test switch
|'''M'''
|'''11'''
|bgcolor="#DD8844"|Mono audio +
|-
|bgcolor="#44FF44"|Video green
|'''N'''
|'''12'''
|bgcolor="#FF4444"|Video red
|-
|bgcolor="#FFFF44"|Video sync
|'''P'''
|'''13'''
|bgcolor="#4444FF"|Video blue
|-
|Service switch
|'''R'''
|'''14'''
|bgcolor="#DDDDDD"|Video GND
|-
|Coin switch #4 P2
|'''S'''
|'''15'''
|Coin switch #3 P1
|-
|Coin switch #2 P2
|'''T'''
|'''16'''
|Coin switch #1 P1
|-
|P2 Start
|'''U'''
|'''17'''
|P1 Start
|-
|P2 Up
|'''V'''
|'''18'''
|P1 Up
|-
|P2 Down
|'''W'''
|'''19'''
|P1 Down
|-
|P2 Left
|'''X'''
|'''20'''
|P1 Left
|-
|P2 Right
|'''Y'''
|'''21'''
|P1 Right
|-
|P2 A
|'''Z'''
|'''22'''
|P1 A
|-
|P2 B
|'''a'''
|'''23'''
|P1 B
|-
|P2 C
|'''b'''
|'''24'''
|P1 C
|-
|P2 D
|'''c'''
|'''25'''
|P1 D
|-
|Select down
|'''d'''
|'''26'''
|Select up
|-
|bgcolor="#DDDDDD"|GND
|'''e'''
|'''27'''
|bgcolor="#DDDDDD"|GND
|-
|bgcolor="#DDDDDD"|GND
|'''f'''
|'''28'''
|bgcolor="#DDDDDD"|GND
|}


RS-485 pair + ground. Use a stereo cable only !
* Sleeve: Ground
* Ring: D-
* Tip: D+


=CD/CDZ=
=CD/CDZ=
==Power supply connector==
[[File:Cdpow_pinout.png]]
See [[power supply]].


==YM2610 digital audio==
==YM2610 digital audio==
[[File:Cd2_cn7.jpg|Cd2_cn7.jpg]]
[[File:Cd2_cn6.jpg|Cd2_cn6.jpg]]
Clock, L, R ?
 
# OP0
# PHI
# SH2
# SH1
# Analog


==Video and CDDA==
==Video and CDDA==
[[File:Cd2_cn1cn3.jpg|400px]]
[[File:Cd2_cn1cn3.jpg|400px]]
R, V, B, S, Burst, GND ?
Clock, L, R ?


==CD reader==
Video:
# Red
# Green
# Blue
# Sync
# Burst
# GND
 
CDDA:
# LRCK
# DATA
# BCLK
 
==CD drive==
[[File:Cd2_cn4.jpg|400px]]
[[File:Cd2_cn4.jpg|400px]]
See [[CD drive]].


==Power==
==PCB power==
[[File:Cd2_cn5.jpg]]
[[File:Cd2_cn5.jpg]]


=Multiplayer jack=
# <span style="color:#7F007F;">Purple: 5V CD</span>
To do.
# <span style="color:#BF7F00;">Yellow: 10V CD</span>
 
# <span style="color:#FF0000;">Red: 5V logic</span>
# Black: Ground


[[Category:Chips]]
[[Category:Chips]]
[[Category:Base system]]
[[Category:Base system]]

Latest revision as of 15:30, 3 May 2021

A/V connector

Note: Some home consoles revisions appear to only provide composite video, no separate sync signal.

Cartridges

Joypad ports

Special, deep DA-15 connectors with a plastic shield. 10 direct inputs, 3 outputs, 2 power lines.

Inputs are pulled high to +5V by CRE401 R-C arrays.

Outputs are open collector through 22 ohms resistors (not pulled high).

JAMMA

See JAMMA connector pinout.

Memory card

See Memory card pinout.

MVS boards

MV4

MV6

Multiplayer jack

RS-485 pair + ground. Use a stereo cable only !

  • Sleeve: Ground
  • Ring: D-
  • Tip: D+

CD/CDZ

Power supply connector

See power supply.

YM2610 digital audio

Cd2_cn6.jpg

  1. OP0
  2. PHI
  3. SH2
  4. SH1
  5. Analog

Video and CDDA

File:Cd2 cn1cn3.jpg

Video:

  1. Red
  2. Green
  3. Blue
  4. Sync
  5. Burst
  6. GND

CDDA:

  1. LRCK
  2. DATA
  3. BCLK

CD drive

File:Cd2 cn4.jpg See CD drive.

PCB power

File:Cd2 cn5.jpg

  1. Purple: 5V CD
  2. Yellow: 10V CD
  3. Red: 5V logic
  4. Black: Ground