Power requirements: Difference between revisions

From NeoGeo Development Wiki
Jump to navigation Jump to search
mNo edit summary
m (Corrected typo and added link to LM2576)
Line 7: Line 7:
Most first generation AES consoles ({{PCB|NEO-AES board}}) are 5V only. Some equipped with the {{PCB|NEO-POWER-0}} board require 9V (see below).
Most first generation AES consoles ({{PCB|NEO-AES board}}) are 5V only. Some equipped with the {{PCB|NEO-POWER-0}} board require 9V (see below).


One way to know for sure is to take apart your console and look for a '''large copper coil and a 5-pin LM2576 chip'''. If both are present, the console requires 9V.
One way to know for sure is to take apart your console and look for a '''large copper coil and a 5-pin [[LM2576]] chip'''. If both are present, the console requires 9V.


=5V AES=
=5V AES=
Line 18: Line 18:


="9V" AES=
="9V" AES=
Considering the 0.5V max drop of the input diode (D1: SR340) and the minimum voltage for the LM2576, the "9V" version AES console should run fine '''starting at 7.5V'''. Using a 5V power supply won't damage anything, it simply '''won't work'''.
Considering the 0.5V max drop of the input diode (D1: SR340) and the minimum voltage for the [[LM2576]], the "9V" version AES console should run fine '''starting at 7.5V'''. Using a 5V power supply won't damage anything, it simply '''won't work'''.


The LM2576 can work up to 45V but the surrounding components were probably chosen to whitstand '''no more than 12V'''. The capacitors are rated at 16V.
The [[LM2576]] can work up to 45V but the surrounding components were probably chosen to withstand '''no more than 12V'''. The capacitors are rated at 16V.


The current draw is around '''750mA at 9V'''. It can be expected to rise up to 1.5A depending on the game played and the use of headphones.
The current draw is around '''750mA at 9V'''. It can be expected to rise up to 1.5A depending on the game played and the use of headphones.

Revision as of 22:38, 24 May 2020

Notes about power supply testing ? Unloaded/loaded voltage ? Max current ? Linear vs. switching infos ?

Also see power supply.

How to identify

Most first generation AES consoles (NEO-AES board) are 5V only. Some equipped with the NEO-POWER-0 board require 9V (see below).

One way to know for sure is to take apart your console and look for a large copper coil and a 5-pin LM2576 chip. If both are present, the console requires 9V.

5V AES

The best idea SNK ever had was to sell a video game console with its power input going straight to all the chips, without any kind of polarity or voltage protection. This probably resulted in many fried consoles and pushed SNK to make the "9V" version.

  • Voltage requirement: 5V +/- 0.2V
  • Current requirement: 2A

Going over 5.2V will more or less quickly kill components. 9V will cook everything. Going under 4.8V can cause glitches or resets.

"9V" AES

Considering the 0.5V max drop of the input diode (D1: SR340) and the minimum voltage for the LM2576, the "9V" version AES console should run fine starting at 7.5V. Using a 5V power supply won't damage anything, it simply won't work.

The LM2576 can work up to 45V but the surrounding components were probably chosen to withstand no more than 12V. The capacitors are rated at 16V.

The current draw is around 750mA at 9V. It can be expected to rise up to 1.5A depending on the game played and the use of headphones.

MVS

To do.

Do not adjust your cab or supergun PSU 5V output above 5.2V (5.15V ?) to compensate for a voltage drop under load. If there's such a voltage drop, the PSU either has a current rating too low, or needs servicing. Increasing the 5V line's voltage might be a temporary solution for spurious resets, but can slowly deteriorate chips in the long run.

CD

To do. See NEO-CDA board.