YM2610 registers: Difference between revisions

From NeoGeo Development Wiki
Jump to navigation Jump to search
m (Playback rate)
Line 276: Line 276:
|}
|}


*Datasheet states playback formula as F=[Delta-N / 256] x 55.5KHz (correct?)
Playback rate is f = 8M / 12 / 12 / (65535 / Delta-N) = 55555 * (Delta-N / 65535) Hz
*Write to flag control to reset/mask channel end flags
 
**Write 1 to reset and/or mask selected flag
* Write to flag control to reset/mask channel end flags
**Write 0 to unmask selected flag
** Write 1 to reset and/or mask selected flag
**Masking a flag will prevent it from being raised when a channel sample reach its end, this means you have to write 1, then 0 to clear a flag and keep it active.
** Write 0 to unmask selected flag
**Flags must be manually cleared, playing a new sample on the channel won't clear it.
** Masking a flag will prevent it from being raised when a channel reaches its end address. This means you have to write 1 to clear the flag, then 0 to keep it active.
** Flags must be manually cleared, playing a new sample on the channel won't clear it.


= Reading =
= Reading =

Revision as of 14:00, 13 November 2016

SSG part

See SSG for details on this part's operation.

Address (Z80 port 4) Data (Z80 port 5)
$00
Bit 7 6 5 4 3 2 1 0
Def Fine tune
Channel A
$01
Bit 7 6 5 4 3 2 1 0
Def - Coarse tune
$02
Bit 7 6 5 4 3 2 1 0
Def Fine tune
Channel B
$03
Bit 7 6 5 4 3 2 1 0
Def - Coarse tune
$04
Bit 7 6 5 4 3 2 1 0
Def Fine tune
Channel C
$05
Bit 7 6 5 4 3 2 1 0
Def - Coarse tune
$06
Bit 7 6 5 4 3 2 1 0
Def - Noise tune
Noise channel
$07
Bit 7 6 5 4 3 2 1 0
Def - /EN noise C/EN noise B/EN noise A/EN C/EN B/EN A
/Enable for Noise and Tone
$08
Bit 7 6 5 4 3 2 1 0
Def - ModeVolume
Channel A
$09
Bit 7 6 5 4 3 2 1 0
Def - ModeVolume
Channel B
$0A
Bit 7 6 5 4 3 2 1 0
Def - ModeVolume
Channel C
$0B
Bit 7 6 5 4 3 2 1 0
Def Volume envelope period fine tune
$0C
Bit 7 6 5 4 3 2 1 0
Def Volume envelope period coarse tune
$0D
Bit 7 6 5 4 3 2 1 0
Def - Volume envelop shape
See diagram.

Timers

Address (Z80 port 4) Data (Z80 port 5)
$24
Bit 7 6 5 4 3 2 1 0
Def TA counter load bits 9-2
$25
Bit 7 6 5 4 3 2 1 0
Def - TA counter load bits 1-0
$26
Bit 7 6 5 4 3 2 1 0
Def TB counter load bits 0-7
$27
Bit 7 6 5 4 3 2 1 0
Def CSM Mode 3 slot modeReset TB flagReset TA flagEnable TB IRQEnable TA IRQLoad TBLoad TA
  • TA = Timer A, TB = Timer B
  • Timers will tick until they have reached zero, at which point an IRQ will be generated if enabled. Reading port $04 will show which timer caused it.
  • The actual timer counter registers are not directly accessable. They can be reset to zero or initialised from load registers $24-$26
    • Writing 0 to the load bits in register $27 will reset the timer counter registers to zero
    • Writing 1 to the load bits will copy the respective timer load register to the timer counter. This only works when the timer is at zero.
  • When a timer expires, it is automatically reloaded from the load registers and continues.
  • Timer flag reset refers to the same flags that are read from port $04
  • CSM mode is for automatic key on for operators on the second FM channel when timer A expires?

FM part

Common FM Registers

Address (Z80 port 4) Data (Z80 port 5)
$22
Bit 7 6 5 4 3 2 1 0
Def - OnControl
LFO Frequency
$28
Bit 7 6 5 4 3 2 1 0
Def Slot -Channel
Key On/Off

LFO Frequency values are as follows:

  • 0 – 3.98
  • 1 – 5.56
  • 2 – 6.02
  • 3 – 6.37
  • 4 – 6.88
  • 5 – 9.63
  • 6 – 48.1
  • 7 – 72.2

Channel Registers

Depending on which channel you want to write to, the ports used are different:

  • Channels 1/2: Ports 4/5
  • Channels 3/4: Ports 6/7

Per-Operator Registers

The ranges given for the address represent all of the parameter values. Each channel's operators are laid out as follows:

Operator 1 2 3 4
Channels 1, 3 $x1 $x5 $x9 $xD
Channels 2, 4 $x2 $x6 $xA $xE
Address (Z80 port 4 or 6) Data (Z80 port 5 or 7)  
$31-$3E
Bit 7 6 5 4 3 2 1 0
Def - DTMUL
Detune (DT) and Multiple (MUL)
$41-$4E
Bit 7 6 5 4 3 2 1 0
Def - Total Level
Total Level (Volume)
$51-$5E
Bit 7 6 5 4 3 2 1 0
Def KS -AR
Key Scale (KS) and Attack Rate (AR)
$61-$6E
Bit 7 6 5 4 3 2 1 0
Def AM -DR
AM On (AM) and Decay Rate (DR)
$71-$7E
Bit 7 6 5 4 3 2 1 0
Def - SR
Sustain Rate (SR)
$81-$8E
Bit 7 6 5 4 3 2 1 0
Def SL RR
Sustain Level (SL) and Release Rate (RR)
$91-$9E
Bit 7 6 5 4 3 2 1 0
Def - SSG-EG
SSG-EG

Overall Channel Registers

The first value listed in the Address column is for channels 1/3; the second is for channels 2/4.

Address (Z80 port 4 or 6) Data (Z80 port 5 or 7)  
$A1,$A2
Bit 7 6 5 4 3 2 1 0
Def F-Num 1
F-Numbers and Block (1/2)
$A5,$A6
Bit 7 6 5 4 3 2 1 0
Def - BlockF-Num 2
F-Numbers and Block (2/2)
(must set this first)
$A9,$AA
Bit 7 6 5 4 3 2 1 0
Def 2CH * F-Num 1
2CH - 2 Slot F-Numbers/Block (1/2)
$AD,$AE
Bit 7 6 5 4 3 2 1 0
Def - 2CH * Block2CH * F-Num 2
2CH - 2 Slot F-Numbers/Block (1/2)
(must set this first)
$B1,$B2
Bit 7 6 5 4 3 2 1 0
Def - FBALGO
Feedback (FB) and Algorithm (ALGO)
$B5,B6
Bit 7 6 5 4 3 2 1 0
Def L RAMS-PMS
Left (L)/Right (R) output, AM Sense (AMS), and PM Sense (PMS)

ADPCM-A part

'Dump' in register $00 is the key on/off bit. Write 0 to start playing specified channels and write 1 to stop playing.

Address (Z80 port 6) Data (Z80 port 7)
$00
Bit 7 6 5 4 3 2 1 0
Def Dump -CH6 ONCH5 ONCH4 ONCH3 ONCH2 ON CH1 ON
$01
Bit 7 6 5 4 3 2 1 0
Def - Master volume
$08~$0D (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def L R-Channel volume
$10~$15 (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 LSB
$18~$1D (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 MSB
$20~$25 (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 LSB
$28~$2D (one for each channel)
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 MSB

ADPCM-B part

Address (Z80 port 4) Data (Z80 port 5)
$10
Bit 7 6 5 4 3 2 1 0
Def Start -Repeat-Reset
Start/Repeat/Reset flags
$11
Bit 7 6 5 4 3 2 1 0
Def L R-
Left/Right Output
$12
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 LSB
$13
Bit 7 6 5 4 3 2 1 0
Def Sample's start address/256 MSB
$14
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 LSB
$15
Bit 7 6 5 4 3 2 1 0
Def Sample's stop address/256 MSB
$19
Bit 7 6 5 4 3 2 1 0
Def Delta-N (L)
Determines sample playback rate
$1A
Bit 7 6 5 4 3 2 1 0
Def Delta-N (H)
$1B
Bit 7 6 5 4 3 2 1 0
Def ADPCM-B channel volume
$1C
Bit 7 6 5 4 3 2 1 0
Def B -A6A5A4A3A2A1
ADPCM-A & B channels flag control

Playback rate is f = 8M / 12 / 12 / (65535 / Delta-N) = 55555 * (Delta-N / 65535) Hz

  • Write to flag control to reset/mask channel end flags
    • Write 1 to reset and/or mask selected flag
    • Write 0 to unmask selected flag
    • Masking a flag will prevent it from being raised when a channel reaches its end address. This means you have to write 1 to clear the flag, then 0 to keep it active.
    • Flags must be manually cleared, playing a new sample on the channel won't clear it.

Reading

The only writable registers that can also be read are from the SSG. All other ports and addresses return different data.

Z80 port # Data Notes
$04
Bit 7 6 5 4 3 2 1 0
Def Busy -Timer B flagTimer A flag
When a timer expires and IRQ is enabled for the timer, the respective bit is set
$05
Bit 7 6 5 4 3 2 1 0
Def SSG register data
Attempting to read non-SSG registers will fail
$06
Bit 7 6 5 4 3 2 1 0
Def ADPCM-B end -CH6 endCH5 endCH4 endCH3 endCH2 endCH1 end
When a channel has reached the end address and stops, the respective bit is set, unless masked
$07 not implemented Always returns $00