CD drive: Difference between revisions
Jump to navigation
Jump to search
m (Split) |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:Cd2_cdboard1.jpg|thumb|right|Top-loading drive control board.]] | [[File:Cd2_cdboard1.jpg|thumb|right|Top-loading drive control board.]] | ||
The part that fails | The part that makes you wait and fails in [[CD systems]]. The ones used in the NeoGeo consoles are very similar to those found in the Sega CD. They're basically enhanced audio CD drives, which are also able to read CD-ROM data tracks. | ||
Made of a control board and an [[optical pickups|optical pickup]]. | |||
The NeoGeo CD top-loading model drive was made by Sony. The [[CDZ]] one was made by Sharp ? | The NeoGeo CD top-loading model drive was made by Sony. The [[CDZ]] one was made by Sharp ? | ||
| Line 13: | Line 15: | ||
=Connections= | =Connections= | ||
Some say the protocol was standard for the time, but clear information is hard to find. This was guessed from the [[system ROM]] disassembly, Sega | Some say the protocol was standard for the time, but clear information is hard to find. This was guessed from the [[system ROM]] disassembly, Sega CD documents and a logic analyzer. | ||
==Top-loading model== | ==Top-loading model== | ||
| Line 274: | Line 276: | ||
| Communication clock to CDC | | Communication clock to CDC | ||
|} | |} | ||
==Adjustment pots== | ==Adjustment pots== | ||
Latest revision as of 18:48, 22 June 2019
The part that makes you wait and fails in CD systems. The ones used in the NeoGeo consoles are very similar to those found in the Sega CD. They're basically enhanced audio CD drives, which are also able to read CD-ROM data tracks.
Made of a control board and an optical pickup.
The NeoGeo CD top-loading model drive was made by Sony. The CDZ one was made by Sharp ?
The control board has:
- A 4-bit mask ROM MCU (Sony CXP5084), taking care of operation sequencing and communication with the NeoGeo.
- A DSP (Sony CXD2500) to process analog data from the pickup.
- A servo controler (Sony CXA1372) to drive the pickup coils for tracking and focus.
- A spindle, sled (and tray) motor driver.
Connections
Some say the protocol was standard for the time, but clear information is hard to find. This was guessed from the system ROM disassembly, Sega CD documents and a logic analyzer.
Top-loading model
Connector pinout, directions are from CDD (CD Drive) to CDC (CD Controller):
| Pin # | Name | Type | Direction | Description |
| 1 | CDCK | Clock | Output | Communication clock to CDC |
| 2 | ? | ? | ? | High ? |
| 3 | /IRQ | Signal | Output | Asks the CDC for a data exchange (low pulse at ~64Hz) |
| 4 | ? | ? | ? | High ? |
| 5 | HOCK | Clock | Input | Communication clock from CDC |
| 6 | D0~3 | Data | Both | 4-bit command/status data bus |
| 7 | ||||
| 8 | ||||
| 9 | ||||
| 10 | ? | ? | ? | ? |
| 11 | BCLK? | Clock | Output | Serial bit clock, should be 44100 * 32 = 1.4112MHz |
| 12 | SDATA | Data | Output | Serial data |
| 13 | LRCK | Signal | Output | I2S word clock, should be 44100Hz. Audio L/R switch for the DAC. |
| 14 | D/M ? | Signal | Output | Data/Music. Low during music playback ? |
| 15 | GND | Power | - | Ground |
| 16 | 5V | Power | - | +5V for logic |
| 17 | 9V | Power | - | +9V for motors and coils |
| 18 | GND | Power | - | Ground |
Missing: /RESET, C2PO, and 16MHz.
Front-loading model
Connector pinout, directions are from CDD (CD Drive) to CDC (CD Controller):
| Pin # | Name | Type | Direction | Description |
| 1 | SGND | Power | - | Ground |
| 2 | SVCC | Power | - | |
| 3 | VCC | Power | - | |
| 4 | WFCK | Clock | Output | Write Frame Clock |
| 5 | GND | Power | - | Ground |
| 6 | SCOR | Pulse | Output | Subcode sync |
| 7 | MUTE | ? | ||
| 8 | SBSO | Data | Output | Subcode data |
| 9 | EXCK | Clock | Input | Subcode clock |
| 10 | EMP | ? | ? | EMPty ? |
| 11 | DOUT | Data | Output | ? |
| 12 | 6MHz | Clock | ? | ? |
| 13 | LRCK | Clock | Output | DATA L or R channel (44100Hz) |
| 14 | DATA | Data | ? | Data stream |
| 15 | BCLK | Clock | Output | DATA bit clock (44100 * 24 * 2 = 2.12MHz) |
| 16 | C2PO | Data | Output | Error flag |
| 17 | DB0~3 | Data | Both | 4-bit command/status data bus |
| 18 | ||||
| 19 | ||||
| 20 | ||||
| 21 | HOCK | Clock | Input | Communication clock from CDC |
| 22 | RESET | Pulse | Input | The name says it all |
| 23 | /IRQ | Signal | Output | Asks the CDC for a data exchange |
| 24 | L-MUTE | ? | ||
| 25 | CDCK | Clock | Output | Communication clock to CDC |
Adjustment pots
To do !