Revision as of 06:53, 3 November 2016

The Z80 can access the YM2610 through two pair of ports. They're usually called Address A, Data A, and Address B, Data B. They're respectively Z80 ports 4, 5, 6 and 7.

Pair A (Z80 ports 4 and 5) concerns the SSG, ADPCM-B, and FM channels 1 and 2.
Pair B (Z80 ports 6 and 7) concerns the ADPCM-A, and FM channels 3 and 4.

See YM2610 registers for a complete definition of the registers.

The Z80's SDA0 and SDA1 lines are directly connected to the YM2610's A0 and A1 inputs. NEO-D0 uses SDA2 to decode the access to the YM2610.

Timing requirements

The YM2610 needs a delay between writes, or else they will be skipped. Some homebrew software produce sound in emulators but not on the real hardware because of this.

Many original sound drivers use small routines with fixed delays to write to the YM2610:

; DE -> YM2610 pair A
; This also works with pair B (ports 6 & 7)
di
ld     a,d
out    ($04),a
; At least 21 T-states here ! (6 NOPs, 5.25us)
ld     a,e
out    ($05),a
; At least 73 T-states here ! (19 NOPs, 18.25us)
ei

Polling the YM2610's busy flag is also a solution.

@@ Line 1: / Line 1: @@
-The [[Z80]] can read and write to the [[YM2610]] through two pair of "ports". They're usually called Address A, Data A, Address B, Data B.
+The {{Chipname|Z80}} can access the {{Chipname|YM2610}} through two pair of [[Z80 port map|ports]]. They're usually called Address A, Data A, and Address B, Data B. They're respectively Z80 ports 4, 5, 6 and 7.
-They're respectively linked to the Z80's ports 4, 5, 6 and 7.
-* Port A (Z80 ports 4 and 5) concerns the SSG, ADPCM-B, and FM channels 1 and 2.
+* Pair A (Z80 ports 4 and 5) concerns the [[SSG]], [[ADPCM codecs|ADPCM]]-B, and [[FM audio|FM]] channels 1 and 2.
-* Port B (Z80 ports 6 and 7) concerns the ADPCM-A, and FM channels 3 and 4.
+* Pair B (Z80 ports 6 and 7) concerns the ADPCM-A, and FM channels 3 and 4.
-Only Data A (Z80 port 5) can be read ?
+See [[YM2610 registers]] for a complete definition of the registers.
-See [[YM2610 registers]] for a complete bit definition of the registers.
+The Z80's {{Sig|SDA0|SDA0}} and SDA1 lines are directly connected to the YM2610's A0 and A1 inputs. {{Chipname|NEO-D0}} uses SDA2 to decode the access to the YM2610.
-The Z80's {{Sig|SDA0|SDA}} and SDA1 lines are directly connected to the YM2610's A0 and A1 inputs. SDA2 informs [[NEO-D0]] that the IO request is for the YM2610.
+=Timing requirements=
+The YM2610 needs a delay between writes, or else they will be skipped. Some [[homebrew software]] produce sound in [[emulators]] but not on the real hardware because of this.
+Many original [[sound driver]]s use small routines with fixed delays to write to the YM2610:
+<pre>
+; DE -> YM2610 pair A
+; This also works with pair B (ports 6 & 7)
+di
+ld     a,d
+out    ($04),a
+; At least 21 T-states here ! (6 NOPs, 5.25us)
+ld     a,e
+out    ($05),a
+; At least 73 T-states here ! (19 NOPs, 18.25us)
+ei
+</pre>
+Polling the YM2610's busy flag is also a solution.
 [[Category:Audio system]]
+[[Category:Code]]

Z80/YM2610 interface: Difference between revisions

Revision as of 06:53, 3 November 2016

Timing requirements

Navigation menu